Make a Super-Simple Bath Cabinet (2024)

ByElizabeth Flaherty

Step 1

Build a Basic Box

• Cut the plywood parts to size.
  • Note: If you don’t have a table saw, click here to learn how to make long, straight cuts with a circular saw.
• To make the short end cuts, use the homemade guide shown in step4.

Step 2

Assemble the Cabinet

• Drill 1/8-in. pilot and countersink holes for the screws using a drill bit that does both at once.
• Attach the top, bottom and cleats to one side, then add the other side.
• Mark the middle shelf position on the sides, slip it into place and screw it.
  • Note: There’s no need for glue.
• Before you drill the dowel holes, make sure the box is square by taking diagonal measurements; equal measurements means the box is square.
• If necessary, screw a strip of plywood diagonally across the back of the box to hold it square.
  • Pro tip: For clean, splinter-free holes, drill the dowel holes with a 3/8-in. brad-point bit,making the holes 1/8 in. deeper than the length of the dowels. That way, you can sink the dowels below the surface of the plywood and fill the holes with wood filler.
• Assemble the cabinet box with glue and screws, followed by wood dowels for extra strength.
  • Pro tip: You can buy long dowels and cut them into short pieces, but dowels precut and fluted for woodworking are easier to work with. This assembly method is quick and easy and gives strong results. But because the method requires lots of wood filler to hide the fasteners, it’s for painted work only. If you want to use stain and a clear finish, biscuits or pocket screws are a better choice.

Family Handyman

Step 3

Drill Shelf Support Holes

• With the box completed, drill holes for the adjustable shelf supportsusing a brad-point drill bit.
  • Note: Most shelf supports require a 1/4-in. hole.
• Drill shelf support holes using a scrap of pegboard to position the holes.
  • Pro tip: Wrap masking tape around the drill bit so you don’t drill all the way through.

Family Handyman

Step 4

Cut Cabinet Doors

• Cut the doors using a homemade saw guide to ensure a straight cut.
• To make a guide, screw a straight 1×3 to a 14 x 18-in. scrap of 3/4-in. plywood.
• Then run your saw along the 1×3 to cut off the excess plywood and create a guide that steers your saw perfectly straight and indicates the exact path of the cut.
• Mark the doors, align the guide with the marks, clamp it in place and cut.
  • Pro tip: And be sure to lay the door face down so any splintering takes place on the back of the door.

Family Handyman

Step 5

Mount Hinges on Doors

• Screw the hinges to the doors 3 in. from the ends.
  • Pro tip: A self-centering drill bit positions the screw holes for perfectly placed hinges. The fronts and backs of louvered doors look similar, so check twice before you drill.
• Stand the doors against the cabinet, setting them on spacers to create a 1/8-in. gap at the bottom.
  • Note: The gap between the doors should also be about 1/8 in.

Family Handyman

Step 6

Position Doors

• Clamp each door into position and screw the hinges into place.
  • Pro tip: Screw the hinges to the cabinet from inside for a foolproof, exact fit. If the doors don’t align perfectly because the box is slightly out of square, don’t worry; you can square the box when you hang it. The hinges also adjust up or down 1/16 in.

Family Handyman

Step 7

Cut the Crown Molding

• Measure the top of the cabinet (including the doors) and cut the plywood crown and base frames to that size.
• Set your miter saw to 45 degrees and cut the crown molding with it upside down and leaning against the fence.
  • Pro tip: Clamp a block to the fence so you can hold the molding firmly against it. Also miter a “tester” section of molding to help you position the sidepieces when you nail them into place.

Family Handyman

Step 8

Nail the Crown Molding to the Frame

• Nail the crown to the frame.
• • Note: Nail the mitered corners only if necessary. If they fit tight and are perfectly aligned, let the glue alone hold them together.

Family Handyman

Step 9

Center the Crown Molding

• To avoid splitting when attaching the crown molding, pre-drill nail holes.
• With the sides in place, add the front piece of crown molding.
• Cut it slightly long and then “shave” one end with your miter saw until it fits perfectly.
• Center the crown on the cabinet and fasten it with screws driven from the inside.
• Center the cabinet on the base and attach it the same way.
• Screw both the crown and the base to the cabinet.

Family Handyman

Step 10

Add a Quick Finish

• Remove the doors and hinges.
• Cover the dowels, nails and screw heads with wood filler and sand the filler smooth.
• Fill any voids in the plywood’s edges.
• Sand the cabinet box, crown, base and doors with 120-grit paper.
• Spray all the parts with a white stain-blocking primer.
• When the primer dries, sand it lightly with a fine sanding sponge.
• Spray on at least two coats of spray paint.
  • Note: High-gloss paint will accentuate even tiny surface flaws, so consider using satin or matte.

Step 11

Hang the Cabinet

• To hang the cabinet, locate studs and drive two 3-in. screws through the top cleat.
• Rehang the doors.
• Close the doors to check their fit.
• Nudge the bottom of the cabinet left or right to square it and align the doors.
• Then drive screws through the bottom cleat.